Human C1QTNF1 ELISA Kit

Human C1QTNF1 ELISA Kit For the quantitative in vitro determination of Human Complement C1q tumor necrosis factor-related protein 1 concentrations in serum - plasma - celiac fluid - tissue homogenate - body fluid FOR LABORATORY RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Insert must be read in its entirety before using this product. ELISAENZYME LINKED IMMUNOSORBENT ASSAYINTENDED USE AND TEST PRINCIPLEThis C1QTNF1 ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures. The Stop Solution changes the color from blue to In order to measure the concentration of C1QTNF1 in the sample, this C1QTNF1 ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the Samples and allow the operator to produce a standard curve of Optical Density versus C1QTNF1 concentration. The conce Ntration of C1QTNF1 in the samples is then determined by comparing the OD of the samples to the standard curve. SAMPLE COLLECTION AND STORAGESSerum - Use a serum separator tube and allow samples to clot for 2 hours at room temperature or overnight at 4°C before centrifugation for 20 minutes at approximately 2000×g. Remove serum and assay immediately or aliquot and store samples at -20°C. Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using heparin as an anticoagulant. Centrifuge samples for 30 minutes at 2000×g at 2- 8°C within 30 minutes of collection. Store samples at -20°C. Avoid repeated freeze-thaw cycles. Cell culture supernates, tissue homogenate and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20°C. Avoiding freeze-thaw cycles. Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.MATERIALS REQUIRED BUT NOT SUPPLIED1. 37 °C incubator2. Standard mic Roplate reader capable of measuring absorbance at 450 nm3. Precision pipettes, disposable pipette tips and Absorbent paper4. Distilled or deionized waterREAGENTS PROVIDED All reagents provided are stored at 2-8°C. Refer to the expiration date on the label. Name 96 determinations 48 determinationsMicroelisa stripplate 12*8strips 12*4stripsStandard(6 vial) 0.5ml/vial 0.5ml/vialSample diluent 6.0ml 3.0mlHRP-Conjugate reagent 10.0ml 5.0ml20X Wash solution 25ml 15mlChromogen Solution A 6.0ml 3.0mlChromogen Solution B 6.0ml 3.0mlStop Solution 6.0 ml 3.0mlClosure plate membrane 2 2User manual 1 1Sealed bags 1 1Note: 1. Standard concentration was followed by:. 40,20,10,5,2.5,1.25ng / ml2 If samples generate values ​​higher than the highest standard, please dilute the samples with Sample Diluent and repeat the assay.PRECAUTIONS1. Do not substitute reagents from one kit lot to another. Standard, conjugate and microtiter plates are matched for optimal performance. Use only the reagents 2. Allow kit reagents and materials to reach room temperature (20-25°C) before use. Do not use water baths to thaw samples or reagents. 3. Do not use kit components beyond their expiration date. 5. Use only deionized or distilled water to dilute reagents. 5. Do not remove microtiter plate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided. 6. Use fresh disposable pipette tips 8. Dis notable acid and sodium hypochlorite solutions. 8. Serum and plasma should be handled as potentially hazardous and capable of transmitting disease. Disposable gloves must be worn during the assay procedure, since no known test method can offer complete assurance that products derived from Rat blood will not transmit infectious agents. Therefore, all blood derivatives should be considered potentially infectious and good laboratory practices should be followed. 9. All samples 11. The Waste should be allowed to stand for a minimum of 30 minutes to inactivate the viruses before disposal. 11. Liquid Waste: Add sodium hypochlorite to a final concentration of 1.0%. Substrate Solution is easily contaminated. If bluish prior to use, do not use. 12. Substrate B contain 20% acetone, keep this reagent away from sources of heat or flame. 13. Remove all kit reagents from refrigerator and allow them to reach room temperature (20-25 ° C) .REAGENT PREPARATION AND STORAGEWash Solution (1X) - Dilute 1 volume of Wash solution (20X) with 19 volumes of deionized or distilled water Wash Solution is stable for 1 month at 2-8 ° C.. ASSAY PROCEDURE1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add 50μl of Standard or Sample to the appropriate wells. Blank well doesn't add anyting.3 Add 100μl of HRP-conjug Alate reagent to standard wells and sample wells except the blank well, cover with an adhesive strip and incubate for 60 minutes at 37°C.4. Wash the Microtiter Plate 4 times.Manual Washing - Remove incubation mixture by aspirating contents of the plate into a sink or proper waste container. Using a squirt bottle, fill each well completely with Wash Solution (1X), then aspirate contents of the plate into a sink or proper waste container. Repeat this procedure for a total of four times. Note: Hold the sides of the plate frame firm when washing the plate to assure that all strips remain securely in frame. Automated Washing - Aspirate all Wells, then wash plates four times using Wash Buffer (1X). always adjust washer to aspirate as much liquid as possible and set fill volume at 350μL/well/wash. After final wash, invert plate, and blot dry by hitting plate ont Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.6. Add 50μl Stop Solution to The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing. 7. Read the Optical Density (OD) The standard curve is generated by plotting the average OD (450 nm) obtained for each of the six Standard concentration on the vertical (X) axis versus the corresponding concentration on the horizontal (Y) axis. 2. First, calculate the mean OD value for each standard and sample. All OD Values ​​are subtracted by the mean value of the balnk well before Result interpretation. 3. To determine the amount in each sample, first locate the OD value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. Intra -assay CV(%) and Inter-assay CV(%)are less than 15%.6. Assay range: 1.25 ng/ml –40 ng/ml.7. Sensitivity: The minimum detectable dose of Human C1QTNF1 is typically less than 1.0 ng/ml.8. Cross-reactivity: This assay recognizes recombinant and natural Human C1QTNF1. No significant cross-reactivity or interference was observed.9. Storage: 2-8°C (Use frequently); six months (-20°C) . 10. QUOTE READ ONH;

Bath/Hair Dry Towels

Name:Microfiber Bath/Hair Dry Towels


Material:80%polyester+20%polyamide or customization


Super absorbent


Size:
1.regular 30*70cm,40*80cm
2. and we can do it according to the customeized size

Weight:300gsm--400gsm or we can provide Customized

Color:customized different printed design

Hair Turban Towel,Magic Instant Dry Hair Towel,Rapid Drying Hair Towel,Hair Drying Turban

Changshu Juhao Clean Textile Co., Ltd. , https://www.juhaoclean.com